• Concrete bricks
• Vertical Holes
• Vertical Holes CLIMABLOCK
• Climablock Mortar
• Climablock Prekia

• Platari 19 – 8x19x19 pcs old. 275
• Twelve – 8x12x19 pcs old. 450
• Nine-piece – 8x9x19 pcs old. 550
• Toilet – 15x20x32 pcs old. 90
• Orthoblock 20 – 20x25x19 pcs old. 100
• Orthoblock 25 – 24x25x19 pcs old. 80

For more information click here

• Dutch 25 x 42 cm
• Roman 28 x 42 cm
• French 27 x 41 cm
• Tops 21 x 42 cm
• Double tile
• Antenna support base
• Ventilation tile
• Double side
• Left side
• Top finishes
• Trimmed tops
• Top quadruped
• Enameled in various colors

• Heracles enhanced
• Basis enhanced
• Heracles enhanced (white)
• Heracles Lysis
• Reinforced CEM II / BM (PWL) 32.5N
• Basis CEM II / AM (WL) 42.5R

Used in concretes, where the participation of aggregates is 75-80% of their mass, their role in creating a durable and cohesive fabric, which will receive the loads of construction, is crucial.

Improvement in the adhesion of fresh mortar. Elongation at coagulation time Increases workability. Gives water repellency to the final masonry. It does not harm metals and is user and environment friendly.

A3 is widely used in any application of cement mortar such as building bricks, plastering, laying of marble and slabs and even for the construction of stone walls and houses.

Lime is a product proposed by the supporters of bio-construction for any type of surface finish of the walls, because it “breathes”, thus allowing a constant exchange of air between indoor and outdoor environment. In general, however, the use of lime is part of ecological standards and its use will replace ingredients with chemical action.

Cement-based mortar, for the preparation of concrete of category XC1-C20 / 25 with a maximum of aggregate grain 8mm.
It has high mechanical strength, volume stability and excellent workability.
It is classified as concrete of exposure class XC1, strength class C20 / 25, according to the Regulation of Concrete Technology (KTS) 2016 and the European standard EN 206.

Ready-made cement-based mortar, for first-hand (cast) plaster, reinforced with polymer resins and special improving additives.
It has high mechanical strength, strong adhesion to the substrate and excellent workability with a plaster sprayer or by hand.
It is classified as a general purpose cementitious coating (GP) of category CS IV, W1 according to the European standard EN 998-1.

Ready-made cement-based mortar, for the base layer (2nd coat) plaster, reinforced with polymer resins and special improving additives.
It has high mechanical strength, strong adhesion to the substrate and excellent workability with a plaster sprayer or by hand, without hanging and without cracking the final surface.
It is classified as a general purpose cementitious coating (GP) of category CS II, W0 according to the European standard EN 998-1.

Ready-made cement-based mortar, for the third coat (final layer) plaster, reinforced with polymer resins and special improving additives.
It has high mechanical strength, excellent adhesion to the substrate, reduced water absorption of the final surface and excellent workability with a plaster sprayer or by hand, without cracking the final surface.
It is classified as a general purpose cement mortar (GP) of category CS II, W1 according to the European standard EN 998-1.

Ready-made cement-based mortar, for smoothing and final finishing of surfaces, reinforced with polymer resins and special improving additives.
It has high mechanical strength, excellent adhesion to the substrate, reduced water absorption of the final surface and excellent workability with a plaster sprayer or by hand, without hanging and without cracking the final surface.
It is classified as a single-layer cement mortar (OC) category CS III, W1 according to the European standard EN 998-1.

Adhesion-enhancing primer based on synthetic resins, quartz aggregates of selected quality and granulometric grading and special additives.
Adheres well to all types of surfaces providing a rough surface resistant to alkaline environment.

Styrene-butadiene (SBR) based synthetic building reinforcement resin with 30% active ingredients (solids), for multiple improvements of the properties of cement mortars.
Does not contain APEO and ammonia in compliance with REACH.
It has a low content of Volatile Organic Compounds (VOCs) in compliance with Directive 2004/42 / EC.

Ready-made dry cement-based mortar, for the construction of any size of bricks, concrete blocks and other building materials.
It has high mechanical strength, strong adhesion to the building elements and excellent workability, without “sitting” from the weight of building materials.
It is classified as a cementitious general purpose masonry mortar (GP) of category M5, A1 according to the European standard EN 998-2.

High requirements, extremely flexible cementitious tile adhesive, enriched with polymer resins.
It has a very high bonding strength and excellent resistance to moisture, frost and extreme temperature changes.
Provides excellent workability, extended open application time and resistance to vertical sliding of the tiles during installation.
It is classified as a cementitious adhesive type C2 TE S2 according to the European standard EN 12004-1.

Fast curing, high performance, two component, polyester based anchoring material.

Suitable for anchoring reinforcing bars and other metal elements in concrete and masonry

Rapid maturation and development of endurance code 10086

EPOXY-RESIN-21 Clear is a two-component epoxy resin, thin, solvent-free, highly penetrating and with excellent adhesive properties. It is applied, after mixing the two components, either in old concrete where it offers excellent adhesion with the new concrete, or it is poured into the cavities and cracks where after its polymerization it creates an excellent and high-strength material.

EPOXY-RESIN-21T is a two-component, solvent-free epoxy thixotropic paste with excellent adhesive properties, suitable for industry, shipping, and construction. It has excellent mechanical and adhesive strengths and does not shrink during drying, withstands acids, alkalis and several organic solvents without causing oxidation.